Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
We have uncovered this great article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround directly below on the net and accepted it made good sense to relate it with you on my blog.
Setting up a tub isn't specifically rocket science, however it does require strong plumbing, carpentry, and sometimes, tiling skills. Replacing an old bath tub with a brand-new one is likewise a reasonably tough task. If the old bathtub is conveniently available, the project can relocate rapidly; if you need to open up a wall surface to eliminate the old bathtub and position the brand-new bath tub, the task is much harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to move out the old tub and set in the new one. Make certain you have qualified on your own for the job as well as are comfortable trying it. Rather than working with a contractor to take control of a halfway-completed project, it is much better to take into consideration using one before you start. Chances are you might require a specialist plumber to make tube links.
This article will assist you set up a new tub in your washroom if you have actually currently acquired a brand-new tub as well as don't require to transform the plan of your previous water pipelines.
Your tools and also product checklist should consist of the following:
Planning for the Installment
First of all, the sustaining framework provided with the bath ought to be fitted (if called for) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the tap includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable tap connectors to the bottom of the two faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you make use of all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now be ready to be fitted in its last placement.
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, after that the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain pipes any type of water staying in the system. The procedure of removing the existing taps can be rather troublesome due to the limited accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will originate from the pipelines. As soon as the supply pipes have actually been removed, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this process. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old sealing substance.
Prior to moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Utilizing the two wooden boards under its feet, place the bath tub in the needed position. The wood boards are useful in evenly spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 tiny points.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bath tub till the spirit level checks out degree.
To set up faucets, fit the bottom of the outermost adaptable faucet port to the suitable supply pipe by making a compression join; then do the same for the other tap.
Activate the water supply as well as examine all joints and also brand-new pipework for leakages as well as tighten them if essential. Fill the bath tub as well as also inspect the overflow outlet and also the regular outlet for leakages.
Lastly, take care of the bath paneling as described in the producer's instruction manual. Tiling as well as securing around the bathtub must wait up until the tub has been used a minimum of when as this will settle it right into its last position.
Suitable New Taps
If the tails of the new taps are plastic, then you will require a plastic adapter to stop damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end gives a link to the existent supply pipes.
If you require to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin guaranteeing that the washers are in place between the tap as well as the sink. Protect the tap in position with the supplier given backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The former type should be attached to the faucet ends first, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to fracture a stiff seal, creating the water to permeate the wall surface between the bath and the tiling, causing complications with wetness and feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and also cartridges, and also are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill up the bathtub with water prior to securing, to permit the activity experienced when the tub is in use. The sealant can break fairly very early if you do not think about this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily readily available on the market. It is recommended to fit the tiles utilizing waterproof or water-proof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader on How to Install a Bathtub Yourself, I figured sharing that piece of content was a good idea. Are you aware of somebody who is very much interested in the subject? Why not share it. We love reading our article about How to Install a Bathtub Yourself.
The right fix? Ring! Report this page